With Christmas rapidly approaching and teacher gifts finally completed, I realized I needed some git bags to pop them in. Scor Pal to the rescue! You can use your Scor Pal to make nearly any size bag you want, and I can show you how.
Based on the size of my gift, I decided to make a bag 6" wide by 2.5" deep. (Sorry, I can't show the actual gifts yet, since they are being given Thursday & Friday and I don't want to spoil the surprise, just in case!) So, it's easy to figure out how much paper you need based on the size of the bag, plus a 1/2" - 1" flap for adhering. Just add up all of the sides: 6 + 2.5 + 6 + 2.5 = 17 Since this is larger than 12 inches, I know I will need 2 sheets of cardstock. I will need a flap on each piece to attach them, and I choose a 1/2" flap, so I will need 2 sheets cut to 9" x 12". The 12" is height plus bottom, so lay your cardstock on the Scor Pal vertically, like this:
Next, score the cardstock for the 2 side measurements and flap.
When you have scored both lines, your cardstock should look like this:
Next, you will rotate your cardstock one turn (90 degrees). It doesn't matter which way you turn it, as long as you do both sheets of cardstock the same way. When you are done, the cardstock will look like this:
 |
| This corner piece I have scribbled through gets removed completely. |
Next, you will cut the flaps for the bottom of the bag:
The arrows I drew in show where pieces are cut to make the flaps. Note that the piece we cut completely out in the previous step is next to a bottom flap. Next, we need to attach the two pieces of cardstock and assemble the bottom of the bag.
Lay your cardstock so the fold of the skinny side flap is a "mountain" fold. Put your adhesive on the top side of this skinny flap on both pieces of cardstock. Now adhere the flap on the first piece of cardstock to the "inside" of the second piece of cardstock. Then adhere the flap on the second piece of cardstock to the inside of the first piece of cardstock.
Next you will put adhesive on the "outside" of the smaller side flaps, and fold over one of the larger side flaps on top of them. Set it flat on the table and push down the smaller flaps from the inside of the bag to make sure they are adhered.
Finally, you will put adhesive on the "inside" of the final flap and adhere it to the rest of the bottom. Your bag is now finished. If you are going to want to put a topper on your bag, you can use your fingers to crease the small sides in half partway down the sides of the bag.
Now, on to the fun part - making the bag pretty! Here is how mine turned out:
I opted for a simple topper since my paper had a pretty design. The 6"x6" paper pads in the store are perfect for this! I just folded mine in half. I wanted to make my bag reusable, so rather than permanently attach the topper, I wanted to tie it on. I held my folded topper over the folded bag and punched 2 holes through all of the layers at once. I used eyelets from my stash to reinforce the holes in the topper only.
Since my paper had a pretty design, I left it alone and just traced over some of the design elements with my Copic Spica pens.
I also traced over some of the stamped elements on this tag with the Copic Spics pens. I reinforced the hole in the tag with another eyelet. I threaded twine through the holes in the bag & topper, then through the tag and tied it in a shoestring bow. Easy to open and easy to reuse! (Note: if you want to see the gifts I made, you can visit
my blog Friday to see them.)
The following products to make this are available in the Cutters Creek store:
Other materials used:
- cardstock in coordinating color(s)
- Cricut Artiste cartridge (for tag)
- stamps of your choice (for tag)
- eyelets and punch (I used a Crop-a-dile)
.jpg)
Posts
